Power Modules for SVG and Active Harmonic Filters
Static var generators (SVG) and active harmonic filters (APF) depend on fast, efficient IGBT power modules. This guide covers topology, ratings, thermal and gate-drive considerations, and how HIITIO's 3-level and 62mm modules fit.
Power quality problems such as low power factor, unbalanced phases and harmonic distortion are now routine in factories, data centers and renewable plants. Static var generators (SVG) and active harmonic filters (APF) address them with power electronics rather than capacitor banks. At the heart of both sits one component: the IGBT power module.

At HIITIO, we design and manufacture IGBT, SiC and gate driver products for power conversion. This article explains what SVG and APF designers should look for in a power module, and where our catalogue fits.
How SVG and APF Work, and Why the Module Matters
An SVG is an electronic reactive power compensator. Circutor’s SVG documentation describes it as working on the same principle as an active filter: it injects a current in the opposite direction to the installation’s non-useful power. Because it has no electromechanical switching stages, compensation is stepless and needs little maintenance.
Many commercial products use a modular three-level inverter. For example, Delta’s PQC series uses a 3-level topology with modular IGBT and DC capacitor components, and users scale capacity by adding or removing modules. Academic work reaches a similar architecture: a published study on a three-level IGBT static var compensator describes a bridge of twelve IGBTs with antiparallel diodes that serves both reactive compensation and active filtering.
The module therefore sets the efficiency, thermal limits and switching speed of the whole compensator.
Table 1. SVG vs. APF vs. passive compensation
| Aspect | SVG | Active Harmonic Filter | Capacitor Bank + Reactor |
|---|---|---|---|
| Main purpose | Reactive power, power factor, voltage support | Harmonic current cancellation | Power factor correction |
| Typical power stage | IGBT inverter (often 3-level) | IGBT inverter (often 3-level) | Capacitors, contactors |
| Response | Stepless, fast | Fast, follows the harmonic spectrum | Stepped |
| Moving parts | None in the power path | None in the power path | Switching contactors |
| Module demand | Continuous current, low conduction loss | Fast switching, margin for peak currents | Not applicable |
Key Selection Criteria for SVG/APF Power Modules
1. Topology. Two-level and three-level converters both appear in power quality equipment. Three-level (NPC or T-type) designs allow lower-voltage devices, lower switching loss and smaller output filters for the same switching frequency.
2. Voltage and current margin. Pick the blocking voltage from the DC-link and grid voltage, with headroom for switching overshoot. Check the repetitive peak current (ICRM) as well as the DC rating, because compensators handle dynamic loads and harmonic peaks.
3. Switching and conduction loss. An APF must generate current at higher frequencies than a basic SVG, so switching energy matters more. Low VCEsat and soft diode recovery also reduce thermal stress.
4. Thermal performance. Look at junction-to-case resistance, maximum operating junction temperature, baseplate material and the integrated NTC. These decide how compact the cooling system can be.
5. Isolation and mechanical fit. Isolation voltage, creepage distance and a pin-compatible footprint shorten development time and simplify second-source planning.
6. Gate driver compatibility. A well-matched driver with short-circuit, undervoltage and overtemperature protection is as important as the module itself.

HIITIO Modules to Consider
The table below maps HIITIO products to common SVG/APF stages. Specifications are taken from HIITIO product pages and datasheets. The “Typical fit” column reflects engineering judgement and should be confirmed against your own design.
Table 2. HIITIO power modules for compensator designs
| Part Number | Package / Topology | Rating | Typical Fit |
|---|---|---|---|
| HCG100FL065E2RB | Easy 2B, 3-level (FL) | 650 V / 100 A | Compact 3-level phase leg |
| HCG150FL065E2RB | Easy 2B, 3-level (FL) | 650 V / 150 A | Wall-mount or rack 3-level units |
| HCG450FL065K1E1 | 3-level, Cu baseplate (size similar to Flow 2) | 650 V / 450 A | Higher-current 3-level modules |
| HCG450FH120A2E1 | 62mm half-bridge | 1200 V / 450 A | Two-level converter stages |
| HCG100FT120K1B | Econo PIM 2H, three-phase | 1200 V / 100 A | Smaller three-phase stages |
Easy 2B 3-Level Modules (HCG100FL065E2RB / HCG150FL065E2RB)
These 650 V modules use a trench gate/field-stop IGBT process and an Al2O3 substrate for low thermal resistance. The HCG150FL065E2RB lists a 125 A DC collector current, 300 A repetitive peak current, 3.0 kV RMS isolation and operation up to 175 °C. HIITIO lists 3-level applications, PCS, UPS and solar among its uses. That makes the family a natural candidate for the 3-level power stage found in many SVG and APF designs.
450 A 3-Level Module (HCG450FL065K1E1)
For higher-current phase legs, the HCG450FL065K1E1 offers 650 V / 450 A in a package sized like Flow 2 with a copper baseplate. Its datasheet provides the typical characteristics, thermal resistance and recovery data needed for loss modelling.
62mm and Econo PIM Modules
Where a two-level topology is preferred, the 1200 V / 450 A 62mm half-bridge is a familiar industrial format. HIITIO’s IGBT module category also covers Econo PIM and Easy packages. The full semiconductor power module catalogue allows filtering by package, topology, voltage and current. For higher switching frequencies or lower losses, the SiC module range is also available.
Manufacturing and Quality
HIITIO states that its power module line includes 10,000-class cleanrooms, 100% X-ray void inspection and HTRB testing, with ISO 9001 and IATF 16949 certifications and compliance with IEC 60747/60749/60068 standards. For a compensator that may run continuously for years, consistent module quality directly affects field reliability.
Gate Drivers and Protection
Switching behavior depends heavily on the gate drive. Wolfspeed’s application note on gate driver design for SiC power modules outlines best practices for drive voltage, protection and layout. The principles apply equally to fast-switching IGBT designs.
HIITIO’s IGBT & SiC driver category includes driver products matched to mainstream packages such as 62mm, EasyPACK, EconoDUAL and Flow. The driver launch announcement lists high driving current, low propagation delay, and overcurrent, overtemperature and undervoltage protection. Pairing a module with a matched driver reduces secondary development and shortens time to market.
Designing to Harmonic Standards
Compensator performance is usually judged at the point of common coupling (PCC). IEEE 519-2022 sets harmonic voltage and current distortion limits at the PCC for installations that contain nonlinear loads. The standard describes steady-state limits, so a design should be validated against both the standard and the local utility’s requirements.
Frequently Asked Questions
Are SVG and APF built from the same power modules?
Often yes. Both are voltage-source inverters, and the power stage can be nearly identical. The difference lies mainly in control algorithms and in how much switching bandwidth is needed.
Why are 3-level topologies common in these products?
Three-level converters allow lower-voltage devices and lower switching loss at a given frequency. Commercial SVG and APF lines, including Delta’s PQC series, use modular 3-level inverters.
Should I choose IGBT or SiC?
IGBT modules remain a cost-effective choice for many compensators. SiC suits designs that prioritize efficiency, size or high switching frequency, at higher initial cost. HIITIO’s technology comparison table on its power module page can help with the first-pass decision.
Can HIITIO support custom requirements?
HIITIO offers technical support and customization for power modules and drivers. Please contact the team with your topology, DC-link voltage and current targets.
Build Your Next SVG or APF Power Stage with HIITIO
Choosing the right module and driver early saves redesign work later. HIITIO supplies Easy 2B 3-level IGBT modules, 62mm and Econo packages, SiC options and matched gate drivers, backed by datasheets, loss data and engineering support. Share your topology, DC-link voltage, current and cooling method, and our team will help shortlist suitable parts and sample options. Browse the HIITIO power semiconductor catalogue or visit hiitiosemi.com to request a quote today.


