SiC and GaN Devices for Totem-Pole PFC
Totem-pole PFC has become a leading choice for high-efficiency AC-DC front ends, but the topology only works well with the right switches. This guide compares SiC and GaN devices, gate-drive needs and design trade-offs, and shows where HIITIO's SiC portfolio fits.
Power supplies for servers, telecom rectifiers and EV chargers keep pushing toward higher efficiency and power density, and the PFC stage is one of the first places designers look. The bridgeless totem-pole PFC has become a common answer, but its performance depends almost entirely on the switches in the fast leg.

At HIITIO, a manufacturer of IGBT, SiC and gate driver products, we see the same question from design teams: SiC or GaN, and at what voltage class? This article walks through the trade-offs using published reference designs and application notes.
Why Totem-Pole PFC Needs Wide-Bandgap Devices
A totem-pole PFC can be viewed as a synchronous-rectifier boost converter. According to Power Electronic Tips, fast wide-bandgap (WBG) switches now allow these designs to run in continuous conduction mode (CCM), which raises both efficiency and achievable power. The same source notes a control challenge: the AC line zero-crossing can create shoot-through risk, so the controller must know when the line changes polarity.
The core reasons WBG devices matter:
- Reverse recovery. In CCM, the fast-leg body diode is hard-commutated every cycle. Silicon MOSFETs suffer from this; SiC and GaN largely avoid the penalty.
- Fewer conduction paths. Removing the input diode bridge reduces the losses of the conventional boost PFC.
- Higher frequency. Lower switching energy allows smaller magnetics.
Efficiency by Topology and Technology
The table below summarizes peak-efficiency figures from a comparison published by Arrow Electronics in a Wolfspeed SiC application article. Treat these as vendor-compiled reference values, not guarantees for any specific design.
| Topology | Peak efficiency |
|---|---|
| Si CrM totem-pole bridgeless | 98.9% |
| SiC CCM totem-pole semi-bridgeless | 98.8% |
| SiC CCM totem-pole bridgeless | 99.1% |
| GaN CCM totem-pole semi-bridgeless | 98.8% |
| GaN CCM totem-pole bridgeless | 99.2% |
| GaN CRM totem-pole bridgeless | 99.1% |
The spread between SiC and GaN is small. In practice, the decision often rests on voltage class, robustness, cost and available gate-drive and control ecosystem rather than on the last 0.1% of efficiency.
GaN in Totem-Pole PFC
GaN HEMTs have no body diode, so they have no reverse-recovery charge. Power Systems Design, in an article by a Texas Instruments GaN marketing engineer, presents this as the main reason GaN suits totem-pole PFC.
A concrete example is TI’s 4-kW single-phase totem-pole PFC reference design, built around the LMG342x GaN EVM and a C2000 controller. It uses a non-isolated current-sense approach and documents efficiency, AC drop, surge and EMI testing, which makes it a useful template for any CCM totem-pole project.

SiC in Totem-Pole PFC
SiC MOSFETs are the other mainstream option. Infineon’s CoolSiC totem-pole PFC design guide covers loss-estimation equations, a selection guide for semiconductors and passives, and a design example with experimental results. The Arrow article above argues that SiC’s avalanche capability, higher operating temperature range and robustness make it an attractive choice, and reports a 3-kW cost comparison in which a SiC solution came out cheaper than equivalent GaN options at the system level. As that analysis comes from a SiC supplier’s ecosystem, validate it against your own bill of materials.
SiC vs. GaN: Design Considerations
| Consideration | SiC MOSFET | GaN HEMT |
|---|---|---|
| Body diode / reverse recovery | Present; handled with careful design in CCM | None; zero reverse-recovery charge |
| Typical voltage classes in PFC | 650 V to 1200 V and above | 600/650 V class |
| Robustness | Avalanche capability and high temperature rating cited by Arrow | Follow the vendor’s layout and drive guidance (see the TI reference design) |
| Gate drive | Negative turn-off bias is common (see HIITIO datasheet conditions below) | Device-specific; follow the datasheet |
| Higher-voltage buses | Available at 1200 V and above | Commonly offered in the 600/650 V class |
Gate Drive and Control Notes
- Negative turn-off bias. HIITIO’s SiC module datasheets list switching tests with negative gate voltage, for example VGS = -5 V/+15 V on the HCS06FH120E1C1 and -4 V/+18 V on the HCS04FC120E2C2. Check your device datasheet for recommended levels.
- Layout. Fast edges make loop inductance critical for both technologies.
- Zero-crossing handling. Plan the polarity-change transition in firmware early, as noted above.
- Isolation and current sensing. TI’s reference design shows one route to simpler, non-isolated AC current sensing.
Where HIITIO Fits
Most single-phase totem-pole PFC stages operating from 230 V mains use 650 V-class switches. HIITIO’s current public catalog is concentrated in 1200 V and higher SiC parts, so our role is mainly in higher-voltage bus designs (for example, fast-charger and industrial front ends), plus supporting components. The products below are listed on our website; confirm suitability against the datasheets.
| Product | Key listed specs | Possible role |
|---|---|---|
| HCD5G06065M | 650 V, 6 A, Qc 22 nC, DFN8x8; page lists “Boost Diodes in PFC” | Boost-diode applications in PFC |
| HCD5G04065A | 650 V, 4 A SiC Schottky, TO-220-2 | Lower-current boost-diode stages |
| HCM32S12T4K2 | 1200 V, 32 mΩ SiC MOSFET, TO-247-4L | Discrete SiC for 1200 V designs |
| HCS06FH120E1C1 | 1200 V, 150 A, 6.2 mΩ, Easy 1B, 175 °C | Module-based higher-power stages |
| HCS09FC120E1Q1 | 1200 V, 9.2 mΩ at 25 °C, Si3N4 AMB, thermistor; apps include vehicle fast chargers | Fast-charger and converter power stages |
You can browse the full ranges under SiC Discrete, SiC Modules and IGBT & SiC Drivers, which lists gate driver cores, plug-and-play drivers and application-specific driver solutions.
Ready to Evaluate SiC for Your Power Stage?
Whether you are prototyping a higher-voltage PFC front end or choosing power modules and drivers for a fast-charger platform, HIITIO’s engineering team can help you match devices to your voltage, current and thermal targets. Browse our SiC modules, discrete SiC devices and gate driver solutions, then share your requirements through the HIITIO contact page or email sales@hiitio.com. We will recommend candidate parts, share datasheets and discuss samples for your evaluation.
FAQ
Is SiC or GaN better for totem-pole PFC?
Neither is universally better. Published comparisons show similar peak efficiency, so the choice usually depends on voltage class, robustness needs, cost and your control and gate-drive ecosystem.
Why can’t a standard silicon MOSFET be used in the fast leg?
In CCM the fast-leg body diode is hard-commutated, and silicon MOSFET reverse recovery causes high losses. SiC and GaN largely avoid this, which is why they dominate CCM totem-pole designs.
Does HIITIO offer 650 V SiC MOSFETs or GaN devices?
Based on our public catalog at the time of writing, our discrete SiC MOSFETs are 1200 V and 1700 V parts, and we list 650 V SiC Schottky diodes. Please contact our team for current availability and roadmap.
What gate voltage should I use for SiC MOSFETs?
It depends on the device. HIITIO module datasheets show test conditions with negative turn-off bias, such as -4 V or -5 V, with positive levels of +15 V to +18 V. Always follow the specific datasheet.



