Grease vs Phase Change Thermal Interface Materials for Power Modules
Thermal grease and phase change materials both fill the gap between a power module and its heatsink, but they age differently. This guide compares process fit, reliability evidence and selection criteria for IGBT and SiC modules.
Every power module datasheet gives a junction-to-case figure, but heat still has to cross one more boundary before it reaches the heatsink. The thermal interface material (TIM) that fills the microscopic gaps there is easy to overlook, yet it can account for a large share of the total thermal path. At HIITIO, a Hangzhou-based manufacturer of IGBT, SiC and Si/SiC hybrid modules, mounting questions are a routine part of module integration. This article compares the two most common choices, thermal grease and phase change material (PCM), and explains how to choose between them.

Why the Interface Layer Deserves Attention
Junction-to-ambient thermal resistance is the sum of junction-to-case, case-to-heatsink and heatsink-to-ambient terms. The middle term depends on the TIM, the flatness and roughness of both surfaces, and the mounting pressure.
HIITIO datasheets show how large it can be. The HCS06FH120E2C1 SiC MOSFET module datasheet lists Rth(j-c) of 0.10 K/W and a grease contact resistance Rth(c-f) of 0.12 K/W, assuming 2.8 W/mK grease at 50 µm. Under those assumptions the interface contributes more than half of the junction-to-heatsink path (0.12 of 0.22 K/W). The HCG450FL065K1E1 datasheet, covering a 650 V / 450 A three-level NPC module with a copper baseplate, shows a similar pattern.
Table 1. Interface contribution in HIITIO datasheet examples (grease, λ = 2.8 W/mK)
| Module / device | Rth(j-c) (K/W) | Interface contribution (K/W) | Stated basis |
|---|---|---|---|
| HCG450FL065K1E1, outer IGBT (Q1, Q4) | 0.16 | 0.08 | Rth(j-h) 0.24 minus Rth(j-c) |
| HCG450FL065K1E1, inner IGBT (Q2, Q3) | 0.18 | 0.10 | Rth(j-h) 0.28 minus Rth(j-c) |
| HCG450FL065K1E1, neutral-point diode (D5, D6) | 0.19 | 0.10 | Rth(j-h) 0.29 minus Rth(j-c) |
| HCG450FL065K1E1, inverse diode (D1–D4) | 0.32 | 0.09 | Rth(j-h) 0.41 minus Rth(j-c) |
| HCS06FH120E2C1, SiC MOSFET | 0.10 | 0.12 | Rth(c-f) listed; 50 µm grease assumed |
HCG450FL065K1E1 interface values are our subtraction of two published figures. Both datasheets assume grease and do not predict PCM performance.
Thermal Grease: Strengths and Failure Modes
Thermal grease is a filled, non-curing paste that flows into surface roughness and can form a thin bond line. It remains the incumbent choice in many designs.
Where it works well
- Controllable layer. Stencil or screen printing gives a defined pattern. Infineon’s EconoPACK and EconoPIM application note documents stencil printing of standard grease alongside its own pre-applied TIM, which shows both routes are established practice.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Limitaciones
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
| Attribute | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
|---|---|---|
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Reported better in thermal cycling (SUNY study); supplier data favourable in power cycling (Henkel) |
| Main process risk | Layer thickness error | Damage to the pre-applied layer before mounting |
| Typical fit | Assembler controls the TIM process | Volume production, repeatable bond line |
What the Cycling Evidence Says
Published results do not point to a single winner. A university comparison of TIM degradation found that PCMs performed better in thermal cycling, while grease was more stable in power cycling.
A supplier case study from Henkel points the other way. In its power module reliability example, active power cycling between −50 °C and 150 °C produced fatal results for two greases after 600 and 800 hours, while LOCTITE TCP 7000, rated at 3.0 W/mK, did not fail at 1,000 hours. The same page reports a thermal impedance of 0.062 for the PCM against 0.160 for grease, roughly 60% lower (units as published; check the source). This is supplier-reported data for one formulation and should be read that way.
The practical conclusion is that the result depends on the specific material, the module construction and the stress profile. Neither category can be assumed superior without testing.
How to Choose for Your Design
- Define the dominant stress. Frequent large load swings stress the interface differently from slow ambient cycling. Match qualification tests to the real mission profile.
- Consider production volume. Pre-applied PCM suits repeatable, high-volume lines. Grease suits flexible or low-volume assembly.
- Check surface flatness. The heatsink and baseplate condition affects both materials. Follow the mounting note for your package.
- Respect the datasheet. Mounting torque and surface requirements are package-specific. For example, the HCG450FL065K1E1 datasheet specifies M5 screws at 3.0–5.0 N·m.
- Measure in your assembly. Datasheet Rth values assume grease at a stated conductivity. A PCM will differ, so verify with your own thermal tests.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
HIITIO supplies IGBT, módulos SiC, Si/SiC hybrid modules y módulos IGBT de alta tensión, with gate drive options in the IGBT & SiC driver range. Formats listed on the power module catalogue include 62mm, Econo Dual, Econo PIM, Easy and E6 packages. Examples include the 62mm 1200 V 200 A SiC module, the 62mm 1200 V 450 A IGBT module y el Econo PIM 3H 1700 V 150 A module. HIITIO states that its production includes 100% X-ray void inspection, which addresses voids inside the module; the TIM then governs the next boundary outside it.
Qualify the Interface with HIITIO
Choosing between grease and phase change material is only half the job; the module, heatsink and mounting process must be qualified together. HIITIO’s power module range cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Preguntas Frecuentes
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.




